EasyCoat®
100% solids epoxy coating for pipes, tanks and metal structures that are buried, submerged or exposed to the weather. Our own product, in 4 L kits ready to mix.
Technical data sheet (PDF, in Spanish)
What it is
EasyCoat is a two-component, 100% solids polyamide epoxy coating, with no solvents or volatile organic compounds (VOC 0 g/L). It is applied by brush, roller or airless spray, up to 250 µm dry film thickness per coat. It can be used as a single coat or combined with other coatings, on prepared steel or on well-adhered aged coatings.
Where it is used
- Exterior of pipelines and piping, buried or above ground.
- Coating repair and weld joints on site.
- Tanks.
- Metal structures exposed to aggressive atmospheres.
Technical data
| Type | Polyamide epoxy, two components |
|---|---|
| Volume solids | 100% |
| VOC | 0 g/L |
| Mix ratio | 1:1 by volume (A:B) |
| Density | 1.41 ± 0.02 kg/L |
| Dry film thickness | Up to 250 µm per coat; up to 750 µm in 3 coats |
| Coverage | 3.8 m²/L at 250 µm |
| Pot life | 60 min at 25 °C |
|---|---|
| Drying at 25 °C | Touch dry, 4 h – hard dry, 15 h |
| Recoat interval | 8 to 24 h; maximum 72 h, sanding if exceeded |
| Full cure | 7 days |
| Service temperature | −30 to +90 °C continuous |
| Storage | 12 months, at 10 °C or above |
How to apply it
Remove the existing coating and degrease the surface with EasyWipe-E®. Then clean by abrasive blasting (Sa 2 / SSPC-SP 6 on above-ground pipes and Sa 2½ / SSPC-SP 10 on buried pipes) or by power tool cleaning to bare metal (SSPC-SP 11).
The surface must be at least 3 °C above the dew point. Apply EasyCoat within 4 h after cleaning.
Pour part B into part A and mix for 5 min. Use the mix within 60 min (at 25 °C) and do not thin it.
Apply by brush, roller or airless spray, up to 250 µm dry film thickness per coat. For higher thickness, apply successive coats every 8 to 24 h.
Check wet film thickness on each pass, dry film thickness at the end, and continuity over the whole surface with a holiday detector.
Before backfilling or immersion, observe the times in the data sheet. On request, we provide the surface preparation and application instructions, including the one for welded joints. Would you rather we apply it? See Recoating.
Packaging
- 4 L kit: 2 L of part A and 2 L of part B.
- 8 and 20 L kits, on request.
- Color: dark gray.
Accessories
-
EasyCoat Preparation Kit: mixing buckets, stirring sticks, gloves and application tools. Assembled to order.
-
EasyWipe-E®: solvent for degreasing and cleaning the surface before applying EasyCoat.
Calculate how much EasyCoat you need
Enter the surface and the thickness. You get the liters, the weight and the kits to request a quote.
Calculation without the calculator: liters = surface (m²) × dry film thickness (µm) ÷ 950 ÷ (1 − losses). Reference losses: 15% with brush or roller and 30% with airless. Example: 100 m² at 250 µm with 15% losses gives 31 L, that is, 8 kits of 4 L.
Fill in the data with values greater than zero.
- Surface to coat
- 101.8 m²
- Coverage at 250 µm
- 3.80 m²/L
- Consumption without losses
- 26.8 L
- Product weight
- 44.4 kg
Takes you to Contact with EasyCoat and the calculation already loaded. If you prefer, send it by WhatsApp or .
Send the request by WhatsAppMix a little at a time
The mix lasts 60 minutes at 25 °C. Prepare only what you will apply in that time.
Estimate based on the coverage in the EasyCoat® data sheet: 3.8 m²/L at 250 µm dry film. Actual consumption may vary with the anchor profile, geometry, applied thickness and application method.
Need EasyCoat?
Request a quote with the number of kits or send us the calculator result.